Installation Guide For Android 11 Developer Preview 2 On Pixel 4
Hey everyone, welcomes back to the Pixel 4 manual website, Today I will share about Installation Guide For Android 11 Developer Preview 2 On Pixel 4, you might probably wait for him to get a taste of all new Android 11 Developer Preview 2 on your Google Pixel device, right then this guide is for you, let’s check how to install or setup Android 11 Developer Preview under Google Pixel devices, so without wasting time. Let’s get started first of all we need to go to settings and enable developer option from the airport font section here, you need tape build number for seven times and confirm your lock screen password to get the confirmation that you are a developer. Now go back to the system and then choose advanced and here you can select developer options, make sure the developer option is on and scroll down to debugging section to enable USB debugging. Now press ok to hello the permission, now you need to make sure some of the pre-requirements like take a full data backup, before installing any firmware for it safely and make sure the Hanser should be charged more than 60%, it’s once everything is good to move on to PC or laptop to install ADB Fastboot file and respective entered USB drivers if you are not aware of all this then there will be a description down below, you can check it out. Now connect your device to PC and download Android 11 developer preview or PA firmware.
I would like to show you how to install side log out using ADB, so you need to download the appropriate OTA firmware file for a device model, in my case, I am using Pixel 4 XL for this, so let me download Pixel 4 XL OTO firmware, once the download gets finished, go to the downloads folder, where use file gets downloaded and cut or copy the downloaded firmware file to the ADB Fastboot folder. We assume that you have already installed ADB and Fastboot tools on your computer and move the OTA file to the install and ADB location. Now open command prompt or power shall be poured shift key from the keyboard and right mouse click, choose open PowerShell window here, now run the command ADB devices and you will get a prompt on your device to allow the connection on your device, tick always hello from this computer and agree on the permission, by selecting hello option. Now once again type the command ADB devices and now it will show a device serial number with the device option. Next to it so both the device into the stock recovery mode using this command ADB reboot recovery, now press enter and now you can see your device get rebooted into stock recovery to know command screen here press, and hold the volume rocker up and power button for at least five seconds, release the volume key to get into stock recovery, both try once again if you don’t get into recovery screen.
Now select the apply update from ADB option on your phone, by navigating using foreign keys and selection by the power button, once you are inside load friend the below command on the PC, once again ADB devices and now it will show a device serial number with the sideload option. Next to the device name that means the device is successfully connected to the PC, inside load mode to install first we need to copy the file name of downloaded ODF file, so let me minimize and copy the file name from the ADB folder and now back to a power strip and type the command on your pc ADB sideload and paste the copied file name, holding control V from the keyboard for our by dot zip at the end of the file name. We can even rename the actual OTA firmware file name, if you can’t copy-paste the file, now press the enter button to get installed now. The firmware file of our updated file should begin to install on your form, this would take a couple of minutes to get finished, if you face any issues in between let us know in the comment session, once done select reboot system now on your for and who do and your device will reboot into Android 11, wait for a couple of minutes as the first boot will take some time, that’s it we have successfully installed at Android 11 Developer Preview 2 on your Google Pixel 4 devices, if you face any issues in between let us know in the comment session, also if you updated to Android 11 for the purpose of testing and you want to downgrade, then we made a guide on how to downgrade from Android 11 to the Android 10 update, there might be quite a few bucks and issue related to Android 11 since it’s still in the development stage. We hope you have found this guide helpful and flashier at the Android 11 our firmware on a google Pixel devices successfully. thank you for reading this Manual installation guide for Android 11 Developer Preview 2 on Google Pixel 4 XL and see you on the next Pixel 4 tutorial.